Off season fun
- Thread starter Danbot
- Start date
D
Danbot
Well-known member
BRRRAAAAAP! I love quadzilla's
Here's my quad that rarely see's the dirt anymore
03 DS650 Baja
Alba Racing stage III exhaust, carb mods, overrev box, bumped timing
Here is my no snow ride.
M
miller tools
Well-known member
summer fun
if you like to swim in
if you like to swim in
M
miller tools
Well-known member
Summer fun
summer fun with the boys
summer fun with the boys
D
Danbot
Well-known member
A whole fleet of Honda bikes! Nice.
I just picked up a box of parts for my cr250 today
. Tonight I start building the engine. Should be able to have the bike together and initially ready for the upcoming season. Next few things on my list are oversize fuel tank, a flywheel weight, and fresh plastic and graphics. I will have to wait until the expensive sledding season is over before I go any further than that. 
I just picked up a box of parts for my cr250 today
. Tonight I start building the engine. Should be able to have the bike together and initially ready for the upcoming season. Next few things on my list are oversize fuel tank, a flywheel weight, and fresh plastic and graphics. I will have to wait until the expensive sledding season is over before I go any further than that.
D
Danbot
Well-known member
Finally got my rear shock linkage rebuilt this evening.... man those thin race straight need bearings are a PITA to change out without a press.
Tomorrow I will probably start assembling the bike, should be in one piece and ready for some break in heat cycles by this time tomorrow. There's still too much snow to ride local, but within 2 weeks I will be able to hit the sand dunes 2 hours out of town. Can't wait!
Tomorrow I will probably start assembling the bike, should be in one piece and ready for some break in heat cycles by this time tomorrow. There's still too much snow to ride local, but within 2 weeks I will be able to hit the sand dunes 2 hours out of town. Can't wait!
H
High Velocity
Well-known member
If you're talking about the Brule dunes, there's still almost two feet of snow on them.
Here's my '91 mustang coupe. Street sleeper. Built it myself, part resto a little show and go. Engine is a 336 inch turbo small block. based from a ford "R" block. Billet crank and rods, je blower pistons, ported aluminum heads, shaft rockers, 78mm borg warner turbo, DFI fuel injection. Getting ready to add methanol injection and a few other other small upgrades for the summer and then finally going to build my 1140 sled, LOL. Just need the stang running good to keep my sanity while working on the sled.
D
Danbot
Well-known member
Nope, just outside GC. But a Hinton friend just went out to the dunes the other day to scout it for me... he said couple more weeks if the weather stays warm!
Here's my '91 mustang coupe. Street sleeper. Built it myself, part resto a little show and go. Engine is a 336 inch turbo small block. based from a ford "R" block. Billet crank and rods, je blower pistons, ported aluminum heads, shaft rockers, 78mm borg warner turbo, DFI fuel injection. Getting ready to add methanol injection and a few other other small upgrades for the summer and then finally going to build my 1140 sled, LOL. Just need the stang running good to keep my sanity while working on the sled.
Nice I miss my 5.0!!! I also had a coupe.... 90, auto, Cobra killer. Now I just have a rusty Supra Targa
I picked up some goodies for my bike today!
Renthal Fatbars, a Tag Metals bar pad, Soft grips, new gloves, and my pre-season maint. parts, plus a sweet sand paddle... have to post a pic later.
Lots of bare ground now, I might even go for a short rip before I go back to work on friday!
I put a new front tire on the 1800 this week. It's bike week in AZ and 98 degrees outside.
D
Danbot
Well-known member
Last edited:
D
