Damn, i want one now!!
Please dont post how fast it goes or anything!
Please dont post how fast it goes or anything!
Powderlites Turbo Nytro MTX install thread
- Thread starter Lococoin
- Start date
I only had a chance to ride it for a bit in november, ive been stuck up in the bush working ever since. Im hoping to get out in the next two weeks and will keep you posted.
My stage 2 is a fricken riot to ride. I'm having trouble with the airfilter icing over.
In the process of building a snorkle for it. This is the most fun I have ever had on a sled. Bar none!!!
In the process of building a snorkle for it. This is the most fun I have ever had on a sled. Bar none!!!
ya ive heard a lot of guys having trouble with that. Im going to be building a snorkel too. Post pics if you have any.
thanks
Finally!
Well, I just got started on the Powderlites Stage 2 Nytro build last night, a little late in the year I know, but I couldn't wait any longer. Got quite a bit done in only three hours.
Not too bad so far.
Well, I just got started on the Powderlites Stage 2 Nytro build last night, a little late in the year I know, but I couldn't wait any longer. Got quite a bit done in only three hours.
Not too bad so far.
S
seano700
Active member
snorkel
Here is what I did for a snorkel. But as you can see I did some cutting. My air intake is a first generation design from PL that uses a 3" elbowed rad hose from the turbo up to the air box, then has a small 3" pipe to join it to the air filter. All I did was purchase a longer piece of pipe and cut the plastic for the filter to fit. Hope the attachement works. Sean
Here is what I did for a snorkel. But as you can see I did some cutting. My air intake is a first generation design from PL that uses a 3" elbowed rad hose from the turbo up to the air box, then has a small 3" pipe to join it to the air filter. All I did was purchase a longer piece of pipe and cut the plastic for the filter to fit. Hope the attachement works. Sean
I am doing mine somewhat like seano700's but I'm making mine so it clears the plastic then I'm putting a 90 degree elbow (which is 3'' radiator hose) then a short peice of pipe about 4" then the filter. This moves the intake away from the exaust and above the seat. Looks kind of funny but by doing this I am hoping it won't be sucking the dry fine snow we have in Montana.
Temps above 15 degrees F. I haven't had any trouble with dave's intake.
Temps above 15 degrees F. I haven't had any trouble with dave's intake.
could this be causing the code to flash? I think I got it connected in the right places but I cannot be sure... I'll have to recheck it. I hope it's that easy...
Sounds like it was just a bad connection... Wow that was good news.... Now just to adjust fuel pressure and load the new map to it...
Thanks, Bull
Thanks, Bull
Last edited:
Trying to connect the bluebike, but I can't figure out the com ports...Is there a map downloaded to the RB3 when we get it? Or do we need to load a map to get the sled running?
I've adjusted fuel pressure to 48-50 psi now. It wouldn't start right away, but I think the battery just might need more power...smells gas so it should get fuel...
No more codes now...Just the RB3 that had a bad connection where the plug gets into the RB3 box. I've heard more guys had this problem to begin with. Not a big problem, just a heads up to everyone. If you get a code in the display, try to connect the RB3 again.
I've adjusted fuel pressure to 48-50 psi now. It wouldn't start right away, but I think the battery just might need more power...smells gas so it should get fuel...
No more codes now...Just the RB3 that had a bad connection where the plug gets into the RB3 box. I've heard more guys had this problem to begin with. Not a big problem, just a heads up to everyone. If you get a code in the display, try to connect the RB3 again.
Last edited:
Ok thanks. Can't get it to fire up....Can't figure why at this point either...
I don't have the USB, but the bluetooth should work in my mind....just hope it will load....The program locks whenever I try to load the bluetooth
I don't have the USB, but the bluetooth should work in my mind....just hope it will load....The program locks whenever I try to load the bluetooth
Yes, I got the Bluebike. Bought the full kit....My computer skills aren't the best, but I should be able to figure it out...
Nevermind. The laptop was the problem. Got a new one now and the rapid bike connection worked, and I uploaded the new map.
Now I just need to figure why it wont fire? Tried disconnectiong the RB3, but that was not the problem. I definatly gets fuel. The pressure regulator shows just below 50 psi. There must be something wrong somewhere with the ignition....If a spark plug fouls, does it produce a code in the display? That's the only thing I can imagine being the problem at this point....
Now I just need to figure why it wont fire? Tried disconnectiong the RB3, but that was not the problem. I definatly gets fuel. The pressure regulator shows just below 50 psi. There must be something wrong somewhere with the ignition....If a spark plug fouls, does it produce a code in the display? That's the only thing I can imagine being the problem at this point....
goin good
The build is goin good so far. Pulled the engine and put the shim in and adjusted the timing, went pretty smooth. Pictures on here were helpful, thanks.
The build is goin good so far. Pulled the engine and put the shim in and adjusted the timing, went pretty smooth. Pictures on here were helpful, thanks.
Good to know...Just take your time, I wish I took more time when I took it apart...would have made things ALOT easier...
My next build will go twice as fast as this one...Alot of thinking and tikering the first time. I wish I was able to call over seas for every question I have. It would make things so much easier.
Anyway, I pulled the spark plugs, they were WET, but they had spark. Now I dried them off and I'm in the prosess of putting them back in. Everything is connected right, so I hope it fires now. If not, I'm lost...
My next build will go twice as fast as this one...Alot of thinking and tikering the first time. I wish I was able to call over seas for every question I have. It would make things so much easier.
Anyway, I pulled the spark plugs, they were WET, but they had spark. Now I dried them off and I'm in the prosess of putting them back in. Everything is connected right, so I hope it fires now. If not, I'm lost...
Still wont fire. No codes. All I have is some whiteish smoke coming out from Air filter. It seems like it wants to start, but it just can't.... I'm really lost at this point... Have NO clue what so ever what it can be...I've got both spark and fuel. Fresh fuel in tank...Could it be that the sled hasn't been started since September, and the fuel in the lines and injectors has water in it?
Reassembly
Anyone got pics of the fuel rail on the 08, I think the 09 might have a few differences. Man, I think even the new directions could be a little better, more pics.
obr, have you tried callin Powderlites? Let us know what is up with that thing.
Intercooler rubber bushings for hangers? I think my kit is missin these, or are they salvaged from somewhere off the stock stuff?
So far we've had to do some grinding and fabin and reworkin of some of the kit pieces, no big deal, but was curious if everyone else had to do the same?
Anyone got pics of the fuel rail on the 08, I think the 09 might have a few differences. Man, I think even the new directions could be a little better, more pics.
obr, have you tried callin Powderlites? Let us know what is up with that thing.
Intercooler rubber bushings for hangers? I think my kit is missin these, or are they salvaged from somewhere off the stock stuff?
So far we've had to do some grinding and fabin and reworkin of some of the kit pieces, no big deal, but was curious if everyone else had to do the same?
obr had it timed 180 degrees off so thats why it wouldnt start. I believe he has it fixed now.
The rubber bushings are from your stock muffler.
Never had to do any grinding. What parts are you needing to modify?
