Deleting Oil Bottle and Pump 800 Rev

[cog]

I know I didn't have to put the hose on the plate but I wanted oil on both sides of the seal, (note hose above plate that is really all you need). It works best if you lift up on the back of the motor move fuel pump, and than raise the back of the sled so you dont drain all the oil out of the case.

 

[i'llDooit]

I know I didn't have to put the hose on the plate but I wanted oil on both sides of the seal, (note hose above plate that is really all you need). It works best if you lift up on the back of the motor move fuel pump, and than raise the back of the sled so you dont drain all the oil out of the case.

with your set up do you have a small oil bottle in place of the old one, and do both lines run to it? also, what is the other nipple to the left of the plate?
Any preferance on mix ratio? 32 or 40 to 1? and why?

 

[lasse]

Any preferance on mix ratio ?
32:1 or 40:1 ?
and why ?

* 40:1 gives you a oil/fuel mix of 2,5 % 2-stroke oil ( Go for it ! )

* 32:1 gives you a oil/fuel mix of 3,1 % 2-stroke oil ( To much, Do not run ! )



.

 

[cog]

 

[i'llDooit]

nice

 

[bjl]

so is mixing the oil in the fuel going to make it smoke more on take offs and when warming it up...

and for doing the math to get the ratios correct i believe u can take your gallons of gas multiplied by 128,, 128 being the amount of oz in a gallon.. then divided by the ratio number that u want to mix. if correct it would be like this mixing 50:1 3 gallons fuel x 128= 384oz of fuel, 384oz of fuel divided 50 being the ratio= 7.68 oz of oil to add to the fuel..

correct me if im wrong please..
thanks

 

[i'llDooit]

what do you do with the low oil sensor? let the light stay on?

 

[cog]

Just unplug, the light does not come on.

 

[sledsrock]

Just unplug, the light does not come on.

^^ what cog said ^^

 

[i'llDooit]

does the block off plate come with the nipple on it, or do you need to add that yourself? i need to get busy on this project. i dont trust the oil pump's consistency.

 

[winter brew]

does the block off plate come with the nipple on it, or do you need to add that yourself? i need to get busy on this project. i dont trust the oil pump's consistency.

No, have to add it.

 

[i'llDooit]

No, have to add it.

thats what i thought. think i will just run the oil line from the nipple above the plate to a gutted fuel filter in place of the 440 res. What is the best thing to do with the oil pump cable? cut it?

 

[maxwellzx]

keep in mind whatever you use as a resevoir has to be vented. think of water in a straw with your finger on the top. if the resevoir is not vented your engine is not getting oil....sorry....your waterpump is not getting oil.

 

[sledsrock]

No, have to add it.

Just wondering.......why do you need the nipple on the plate? I have seen the 800HO Trygstad mod motors with no nipple and the 440 race motor uses no nipple.

 

[i'llDooit]

Just wondering.......why do you need the nipple on the plate? I have seen the 800HO Trygstad mod motors with no nipple and the 440 race motor uses no nipple.

dont know. maybe air when toppin it off? not really sure. how about the oil pump cable,,,,, cut it?

 

[sledsrock]

I just coiled my oil pump cable up and zip tied it out of the way for now. (I have plans down the road to use it as a control for a full throttle switch)

 

[i'llDooit]

I just coiled my oil pump cable up and zip tied it out of the way for now. (I have plans down the road to use it as a control for a full throttle switch)

 

[sledsrock]

Okay look, here is an example of what a oil cable can be used for.....I know, I know it looks like a science experiment......lol

 

[Stuck one]

so can you use the skidoo semi-synthetic oil for the premix or not

 

[sledsrock]

so can you use the skidoo semi-synthetic oil for the premix or not

Yep, you can use it for premix.