NEW Belt Guard Protection from Skinz!

[Sled Solutions]

1/4" UHMW same as the float plates

Unlike aluminum guards if you hit something these will bounce back ready for the next hit.

Made in the U.S.A.

Available now! $44.95

http://www.sledsolutions.com/store/product_info.php?products_id=1340

Thanks,
Paul

 

[jhurkot]

Also snow won't stick to them either. I'll probably go this route.

 

[Sled Solutions]

Also snow won't stick to them either. I'll probably go this route.

Yes, good point!

 

[Blown Motor]

Pretty slick idea! I like the non stick feature, and the fact that it will flex a bit but not break or stay dented. Might need one for my pro!

 

[M8fever]

It doesnt cover the hole that lets snow in.

 

[rmscustom]

Exactly what I've been looking for... A plate made of non stick material and I could care less about the hole that lets the snow in, I think it might even help on belt temps, 1300+ miles on original QD belt with snow sometimes packed around it up to the top pulley.

 

[Sled Solutions]

Pretty slick idea! I like the non stick feature, and the fact that it will flex a bit but not break or stay dented. Might need one for my pro!

Hook it up!

Exactly what I've been looking for... A plate made of non stick material and I could care less about the hole that lets the snow in, I think it might even help on belt temps, 1300+ miles on original QD belt with snow sometimes packed around it up to the top pulley.

Look no further!

 

[sledneck_03]

Hook it up!



Look no further!

any insight if they will make them with the drain hole covered? would be easy for them. less cutting.

This is great, on my sport quads, my last one has a plastic skid plate, it takes a beating and bends back, aluminum bends and stays bent.

Also whats your shipping to canada like? do you do ship USPS?

 

[Sled Solutions]

any insight if they will make them with the drain hole covered? would be easy for them. less cutting.

This is great, on my sport quads, my last one has a plastic skid plate, it takes a beating and bends back, aluminum bends and stays bent.

Also whats your shipping to canada like? do you do ship USPS?

We ship USPS Priority Mail to Canada, haven't shipped one yet but guessing around $35.

 

[sledheadd]

Nice product.

 

[Sled Solutions]

 

[akmclean]

Looks great but has no application for the 13's - there is still the giant gaping hole...

 

[Sled Solutions]

Skinz has removed the drain hole and will be providing a template if you'd like to add it.

 

[Jigga99]

I ordered this came in less than a week, great product perfect fit and lines,
basically a skidplate for the right side

 

[Timbre]

Saw one installed on a Pro in one dealer's booth at the Boise snow show. Looked so good, i went straight to the dealer's shop and bought one
I think this is going to be a great addition to the new sled.

Cheers!

 

[geo]

Made my own 1/4" UHMW plate last year.

Good tough start but if your a log hopper or wish to lift you sled in this area you still need to support from the inside. The stock plastic (which this skid plate mounts to) is the weak link in the structure meaning it will still bend up into the pulley with the sled and your weight on in.

I wanted bullet proof for a "hit" situation (like a mistake LOL), so my second attempt had the skid plate mounted through existing rivet holes and couple of new ones to the edge of the tunnel-bulk head-running board-foot well.
Inside I added a 1/2" aluminum angle frame I bent up and tigged the corners. This was mounted in front of the pulley-well , sandwitched the skid plate to the original plastic and was also attached with the rivets to the bulkhead.
This added quite a bit of extra structure utilizing the added skid plate. I can now lift that side with a bottle jack and bounce on the machine and the plastic never touches the belt or pulley.

 

[Sled Solutions]

Belt guards are in stock!