Clean Handle Bars

[nmmiles]

Looking to get rid of the stuff on the left side of my handle bars. All I wan't is a brake handle and a P.E.R.C button.

What brake handle fits the stock brake line?

Where do I get just the single PERC button? Is it all plug and play or do I need to solder them in?

Is it possible to go to the newer style headlight/heaters swiches where they are on the console rather than the handle bars?

Thanks,
Nolan

 

[HUNDO]

The Wilwood brake m/c assembly works but you have to use an adaptor fitting...no big deal, pick it up at any parts store

 

[nmmiles]

Do you have a link to that?

 

[Fast Freddie]

Handel bar clean up

Nmmiles
Hear is a post i did a few weeks back!. It's on 900 tread( taller seat paige4/5 2 paige of post) wilwood master brake, new brake line to fit wilwood, poo. switches soldered in, 09 rev. perc button. hope this helps pm me if you have ?

Fast Freddie

 

[ghostwhite]

Nmmiles
Hear is a post i did a few weeks back!. It's on 900 tread( taller seat paige4/5 2 paige of post) wilwood master brake, new brake line to fit wilwood, poo. switches soldered in, 09 rev. perc button. hope this helps pm me if you have ?

Fast Freddie

How well did the new console fit on our chassis?

 

[Snowbyrd]

Nmmiles
Hear is a post i did a few weeks back!. It's on 900 tread( taller seat paige4/5 2 paige of post) wilwood master brake, new brake line to fit wilwood, poo. switches soldered in, 09 rev. perc button. hope this helps pm me if you have ?

Fast Freddie

I think this will help Fast Freddie

Link To Fast Freddie Post

 

[Ex-Member]

The buttons are exactly that... buttons. They close a circuit when pressed.

Mountainhorse had a link to some billet kill switches, those may work. Also check out , he's got a handful of machined perch switches that i'd bet would look pretty slick on a sled.

 

[Fast Freddie]

09 Console

How well did the new console fit on our chassis?

Fit is ok! just a bit bigger gap between tank & console then i would like. About 3/8" but not much more then my 09 dragon mabe a 1/8" i can live with that.

FF

 

[Fast Freddie]

I think this will help Fast Freddie

Link To Fast Freddie Post

THANKS SNOWBYRD
Was not sure how to do that. ??

 

[06 RMK 900]

Hmm was in the dealer the other day and really liked the look of the clean handle bars and the swithces on the console. I think I might try to do this. So i'm thinking I just find the wires going to the swithces on the bars disconnect them and wire them into the new swithes...Could it be that easy?

 

[ghostwhite]

Hmm was in the dealer the other day and really liked the look of the clean handle bars and the swithces on the console. I think I might try to do this. So i'm thinking I just find the wires going to the swithces on the bars disconnect them and wire them into the new swithes...Could it be that easy?

It takes a little bit of time to figure out which wire is which and if you are any good at wiring and basic wiring theory then yes you can. Dealer switches are hella expensive though... I have an extra perc switch I will send you for just shipping. I ordered two of the wrong one.

 

[06 RMK 900]

It takes a little bit of time to figure out which wire is which and if you are any good at wiring and basic wiring theory then yes you can. Dealer switches are hella expensive though... I have an extra perc switch I will send you for just shipping. I ordered two of the wrong one.

All get back to you. Going to take a look at how many wires there are and price out some new swithes and brake controller. If I can put a new wire harness in a pickup I think I should be able to handle this.

 

[06 RMK 900]

Would anyone happen to know the part numbers for the three switches?

Never mind I found them.

 

[ghostwhite]

the headlight and mode/set are around 30$ from babbits. you can get a switch for a wilwood master cylinder or change out the brake line to use a banjo bolt switch like this one at the caliper

 

[ghostwhite]

Sku: 4011319 switch-handwarmer,spdt
sku: 4012090 switch-mode/set
sku: 4012091 switch-headlight,hi/lo

 

[06 RMK 900]

From looking on babbits I think it would be cheeper to just buy the entire 09 Dragon break handle set up with switch for $140.

 

[WestMont]

From looking on babbits I think it would be cheeper to just buy the entire 09 Dragon break handle set up with switch for $140.

I've checked into buying the entire brake assembly a couple different times from our local dealer and even though the part numbers were valid they said the part wasn't availble. Anyone else run into this?

 

[06 RMK 900]

I would order them from babbits

Number 1 on parts list.

http://www.babbittsonline.com/pages/parts/viewbybrand/default.aspx

I looked at it when I got home and this might have to wait tell next year because funds are short to spend on the brake assembly.

 

[WestMont]

Thanks for the link 06 RMK 900.

 

[06 RMK 900]

The link should have took you right to the diagram but it didn't. If you look under poo 2009 Assault and under brake it is all there. Also if you click on console drop down it gives you part numbers for all the switches.