clutching

Hi guys - a friend of mine is going to ride out west with us this year and had some questions. I'm not uber familiar with what Skidoo has been up to the past couple years but hopefully you can help. His sled is a 2012 Renegade with the 600 Etec. Track is a 137x1.25 and is dialed in for sea...

Anyone know a good set up for the PC M8 for 0-3000 ft. elevation? Is a new torque arm/helix necessary or can you get away with just heavier weights (75g-80g) in the primary? Thanks for any suggestions

hey. does anyone know what the original clutching is on this snowmobile? And what do you recommend if i want to get more acceleration?

Hey, i just bought an 05 M7 that is all stock with a 153" attack 20 track. I just bought some Cutler IT adjustable weights and was wondering if anybody knows or has seen any elevation charts for the M7. I need to know how much to load up the weights for each elevation. At home i am at about 1600...

i have rode polaris snowmbiles since i could walk, but just fell into a deal i couldnt pass up on a 2011 hcr. with the polaris sleds i know who to talk to and know enough about them to get them clutched right and run good stock, but with the cat... im needing some help!! im sure the stock...

I just bought a m7 with a racin station 800 big bore. When i start accelorating it runs good till 6000 ish rpm then it bogs hard but if i keep on the throttle for a bit once it hits a point it opens up and rips but theres that area of bog? Is this a clutching issue or a issue with the fuel...

Okay so I´ve searched and found lots... To much. buddy has 07 1000 with 162 challenger, put on full BMP single exhaust and BD box. Tuned in to 172hp on dyno just below 7600. Ran with a BMP clutch kit (tortion) and 88gr supertips before pipe, overrev. Now running 92gr with BMP exhaust, still...

I have a 07' Skidoo XRS 151" and I think is is time to re-work the clutching ie new springs weights etc. I've riden twice this year and I am on getting about 7700 rpm at best at the higher elevations. What suggestions do you gus have.

I bought a 2003 vertical escape this summer with a broken crankshaft, put a new crank in, and took it out for the first day of the season today. If seemed to run really well on the trail, but once i started getting into a little powder and climbing little stuff I was floored basically the whole...

Sled: 03' 600 RMK 144" track, bone stock. 2500 miles. Just went through most of everything for maintance: replaced driveshaft bearing, cleaned VES valves, fixed a coolant leak, cleaned carbs & clutches, changed chaincase oil, pulled skid out & apart to regrease everything, removed sway bar...

I have some parts for sale from an 08 XP, 154". Sled had about 600 miles on it. 420613925 Cylinder Head Cover ($150) 504152763 outer chain case cover ($130) 504096200 20 tooth top gear ($30.00) 504152593 45 tooth bottom gear ($60.00 504152579 chain ($50.00) 417222508 ramps #413...

Arctic Cat Parts Online Look-up 1974 to 2011 Arctic Cat Drive Clutch and Driven Clutch Component Part Numbers and Specs. Cat Torque/Tech/Specs How to read spark plugs M8 2010 M8 Broken Primary Springs (Something to check) D&D big dog weights vs. cat weights 07-09 M8 Clutching setups...

I just picked up a 99 ZR440 SnoPro 136 x 2 for my 9 year old son to ride. I want to gear it down as far as possible and mess up the clutching to slow it down enough for him to live into his teenage years. What is the lowest gear combination that will fit in the stock chaincase? If I drop the...