V
Velislide
New member
Just not having much time for sledding at all lately, moving into new house, starting new job, fixing vehicle, etc etc... Anyways, I put alot of time and work fixing this sled up, got the new chassis to drop everything into, but just have no time lately for much of anything. Well heres what I got.
=== 1998 ZR600 EFI Limieted Edition (Black) ===
Bought this sled from a friend for about 1100$ as it needed quite a bit of work, sled had a weak spark and would foul plugs alot, but after going through the electrical system on it (I thought it was the stator, glad it wasnt the case), i found THREE broken grounds, and fixed them all, and has yet to foul again, and runs great now, almost always starts second pull, even in this -10 weather. The 1998 chassis had two cracks in the bulkhead that I didnt want to mess with welding (still rides good with the cracks lol), but I figured I wanted a newer chassis anyways, and since the engine has been rebuilt (less then 1100 miles on it now), I have a good engine, track, suspension, so I was going to transfer it all over, but no time now. Also the bellypan and front bumper of the ZR2 chassis has seen better days, and is cracked and broke in a few spots under it.
New 8" HJC Billet Riser
New Fly Aero Snow-X bars
New ODI Grips & Heaters
New Firecat throttle assembly
New Firecat brake lever assembly (loved how the lever is the bright/dim switch)
Black Sportech Hand guards
Rear suspension completely gone thru & parts cleaned / replaced, rails painted black
New 1998 SnoPro rear torsion bars with less then 250 miles on them (love those, HUGE difference for me @ 180lb)
Low trimmed Sportech windshield
New chain in the chaincase
New bearings jackshaft
121" Ripsaw track with less then 1200 miles on it, looks great, and hooks up GOOD!
Additional set of 2005 Firecat Skis (black w/ orange handles) included
D&D Clutch Setup
D&D Super Single pipe
D&D Performance Chip
All I can think of at the moment, in a hurry as its late lol, heres some info about the ZR3 chassis
The chassis consists of the Bulkhead, front bumper, bellypan assembly, tunnel, and a 144" tunnel extension (the GOOD looking ones, not the super fat ugly ones haha), and heat exchangers, and an extra brake disk. Motor mounts for the old 800cc engine are there also, the voltage regulator? or whatever is mounted behind the right side footwell is there, along with the whole wiring harness for the snowmobile. The chassis is in great condition, no cracks or broken mounting points on the bulkhead / bellypan.
I'll try to get pictures as soon as possible, sled looks really good right now as it is, all black!
Asking 1750$ for EVERYTHING, and I dont have time to mess with any shipping on anything, sorry!!!
=== 1998 ZR600 EFI Limieted Edition (Black) ===
Bought this sled from a friend for about 1100$ as it needed quite a bit of work, sled had a weak spark and would foul plugs alot, but after going through the electrical system on it (I thought it was the stator, glad it wasnt the case), i found THREE broken grounds, and fixed them all, and has yet to foul again, and runs great now, almost always starts second pull, even in this -10 weather. The 1998 chassis had two cracks in the bulkhead that I didnt want to mess with welding (still rides good with the cracks lol), but I figured I wanted a newer chassis anyways, and since the engine has been rebuilt (less then 1100 miles on it now), I have a good engine, track, suspension, so I was going to transfer it all over, but no time now. Also the bellypan and front bumper of the ZR2 chassis has seen better days, and is cracked and broke in a few spots under it.
New 8" HJC Billet Riser
New Fly Aero Snow-X bars
New ODI Grips & Heaters
New Firecat throttle assembly
New Firecat brake lever assembly (loved how the lever is the bright/dim switch)
Black Sportech Hand guards
Rear suspension completely gone thru & parts cleaned / replaced, rails painted black
New 1998 SnoPro rear torsion bars with less then 250 miles on them (love those, HUGE difference for me @ 180lb)
Low trimmed Sportech windshield
New chain in the chaincase
New bearings jackshaft
121" Ripsaw track with less then 1200 miles on it, looks great, and hooks up GOOD!
Additional set of 2005 Firecat Skis (black w/ orange handles) included
D&D Clutch Setup
D&D Super Single pipe
D&D Performance Chip
All I can think of at the moment, in a hurry as its late lol, heres some info about the ZR3 chassis
The chassis consists of the Bulkhead, front bumper, bellypan assembly, tunnel, and a 144" tunnel extension (the GOOD looking ones, not the super fat ugly ones haha), and heat exchangers, and an extra brake disk. Motor mounts for the old 800cc engine are there also, the voltage regulator? or whatever is mounted behind the right side footwell is there, along with the whole wiring harness for the snowmobile. The chassis is in great condition, no cracks or broken mounting points on the bulkhead / bellypan.
I'll try to get pictures as soon as possible, sled looks really good right now as it is, all black!
Asking 1750$ for EVERYTHING, and I dont have time to mess with any shipping on anything, sorry!!!
