EVOLUTION POWERSPORTS 1100T Cold Air Intake

[Evolution Powersports]

Here are pictures of our cold air intake for the 1100T. This intake fits 100% under hood and under factory plastic. It eliminates the stock PITA air filter. The stock filter is supposed to draw from the area behind the windshield, but the fact is the hood/filter/ filter cover is so sloppy that much of the air it draws comes from under the hood right next to the exhaust manifold. The EVOPS intake allows you to draw all air from the dash area.

Best of all, on our Big Chute/Holeshot and Super Chute/Slingshot turbos, our intake makes 5 hp more than stock above 8000 rpms.

This cold air intake is for snow use only.

These will be in stock in 4 weeks. Pre orders will be up on our website shortly.

Price is $259.99

 

[Hillclimbpro]

Using this intake setup does a person need to get a roll over valve? If the sled was rolled and oil leaked into the intake hose wouldn't the oil go right into the turbo?

 

[Evolution Powersports]

Using this intake setup does a person need to get a roll over valve? If the sled was rolled and oil leaked into the intake hose wouldn't the oil go right into the turbo?

Chris,

We are recommending (strongly) that mountain guys use roll over valves with this intake.

 

[type_a_positive]

So this setup only uses the prefilters on the hood? No internal paper filter like stock?

 

[Evolution Powersports]

So this setup only uses the prefilters on the hood? No internal paper filter like stock?

Correct

 

[Evolution Powersports]

So this setup only uses the prefilters on the hood? No internal paper filter like stock?

Yes, the hood mesh is the only filtration. It will be important for guys to verify the condition of this material on your sled. If there are any rips or places where it is not bonded they will have to be fixed prior to running our intake. The mesh that Cat is using on the area behind the hood is that same material they have been using for years on two strokes. Also, most two stroke turbos use the same material for filtration.

 

[0neoldfart]

Good job, but...

Great job on the intake Jim. Only problem is JustBoostIt is now going to get more of my $$$ lol. Maybe I should just mail you guys my paycheques, and you can just ship stuff as it's built...

 

[damx]

Looks good I did the same thing with 2" PVC pipe, with the stock set up oil goes into the turbo also just the paper filter helps sock it up abit.

 

[Matte Murder]

Nice. A guy could easily run two aftermarket style filters too. The ones that look like a perforated can with a "sock" over it?

 

[10003514]

Can all the stock air box be cut out then?

 

[Evolution Powersports]

Can all the stock air box be cut out then?

It can be, but we put the plastic back on to add a layer of insulation between the engine compartment and the silicone.

 

[metcalf]

Is there a problem with your web site? I am having trouble making an order.

 

[Evolution Powersports]

Is there a problem with your web site? I am having trouble making an order.

I will check - If you are still having problems tomorrow, please call the number in my signature.

 

[Matte Murder]

Will the intake get hot from underhood temps? Would some of that gold heat shielding help keep the intake air cooler?

 

[HeavyT]

What roll over valve do you recommend? Do you guys have one of your own?

 

[voodoo]

I believe Frogskinz makes a vent that fits the stock intake locations. They typically stick down better than stock.

 

[Cold_puss]

I assume available in Orange??

 

[madmax]

What roll over valve do you recommend? Do you guys have one of your own?

Stay posted, coming soon.

 

[Evolution Powersports]

I assume available in Orange??

Black only for now.

 

[Sage Crusher]

ROV

Jim
you guy's comming out with a ROV?