Boondocker Timing Module

[dmkhnr]

Just got 2 timing modules from boondocker, and no instructions.
Anyone use these yet? Where do they install?

 

[turboless terry]

I think mine is at the post office. They are supposed to plug in where your ethonal chip goes. Other than that i don't think you have to do anything. Not 100% positive.

 

[Liv4snow]

They plug into your crank position sensor. It is located on the front of your clutch cover. It is a black plug with 5 or six wires in it. you Need a couple of pics or small screw drivers to take it apart.

 

[rubymountainrider]

have you got to try it out ?

 

[Liv4snow]

Yes it has defiantly cleaned things up a lot. Ran great all day here in mcall today at 8.5 lbs of boost. But I think my new silber runs better.

 

[dmkhnr]

I found it. Black connector with 5 wires above the clutch cover. Going to run mine tomorrow.

Have you gotten a clean 10# out of the boondocker? I hear the Sibler is running the best, what kind of boost you seeing?

 

[turboless terry]

Sorry I told you wrong. The prototypes plugged in where the ethanol chip was. Trying it out in the morning,

 

[Kestrel2126]

Yes it has defiantly cleaned things up a lot. Ran great all day here in mcall today at 8.5 lbs of boost. But I think my new silber runs better.

Just curious, in what aspect do you feel the Silber is running better? Are they both Pros? Same fuel? same clutching? same Boost psi?

 

[Liv4snow]

The silber kit runs much cleaner on the bottom end. I can run the silber at 10 lbs at 5000 ft on strait av all day long. The bd starts running out of injector at about 8 lbs. The silber has 2 more injectors. Plus the guy didn't tell me I was a whiner and didn't know how to ride a sled. I paid to fly a rep from there company at my expense to make our sleds run and still nothing. If it wasn't for Justin at code red we never would have gotten anywhere. I thought the reason we bought a bd kit was because they were the best man was I wrong. Bd customer service is the worst I have ever seen.

 

[Liv4snow]

Yes they are both pros sorry got off track.

 

[HighmarkerX]

Will this module work on non turbo sleds? DTR found gains by adjusting timing just wondering if it this could be used on NA sleds. I can't find any info about it...

 

[dmkhnr]

Will this module work on non turbo sleds? DTR found gains by adjusting timing just wondering if it this could be used on NA sleds. I can't find any info about it...

Boondocker says a stock sled will benefit greatly from this module. That is just what they told me, I have no first hand experience.

 

[TEC800]

how about boosted D8's?

 

[Eli]

I thought I would bring this to the top and see how the timing modules worked out. Are they still available from Boondocker for the Dragons?

 

[m1kflyingtiger]

Those that used this with a turbo, when you installed the module did you have to re-tune the sled, or just increas boost an call her good?

 

[hypnotoad]

should just be plug in and go

 

[dmkhnr]

Last year it was a 3* timing change. This season you can specify 1, 2, or 3*.

 

[Eli]

Last year it was a 3* timing change. This season you can specify 1, 2, or 3*.

What did you think of the module?


Sent from my iPhone using Tapatalk

 

[440dart]

common sense on a boosted sled that it would pull timeing? and on a n/a you would want to add timing?

So what does this box do does it + or - timeing if its adding timeing under a boosted aplication then theres ton to gain with added timeing on a n/a engine

 

[dmkhnr]

The timing module worked great for me. BD recomends I stay with the 3*. It takes all of 1 minute to install.