AKBoards

[907riders.com]

Just finishing the final details on our AKBoards for the pro chassis. Assault chassis is next.

These boards are tested tough. We guarantee you will be happy with these running boards.

All stainless steel fasteners are provided

 

[MN_SUMMIT]

What does a set of those boards go for? Also, do you do powdercoating on them??

 

[907riders.com]

Full set comes with Stainless steel hardware, copious amount of ice screws, drill bit for screw installation and detailed instructions with phone support.

AKBoards are different in which the will not be as prone to collect snow at the tunnel. We use flat stock for the tunnel mating and instruct the installer drill and rivet from the inside of the tunnel landing in the tube.. Makes for a clean & strong installation.

$375.00 natural or 435.00 powder-coated

Shipping is $30.00 or less to lower 48

Canadian shipping is $36.00 to most areas

866-610-0456

 

[tdblakes]

you have any pics of these installed on a Pro? Do you cut off the entire lip of the tunnel that the airframes use for mounting and rivit yours to the side of the tunnel instead?

 

[tbeaton]

what are they made of? are they any wider than stock?

 

[907riders.com]

We leave 3/8" on the lip. It distributes the load better. No pics installed yet. AKBoards are being powder coated.

We are incorporating a tunnel brace into this design to strengthen the tunnel at the rear suspension mount.

 

[skippy]

We leave 3/8" on the lip. It distributes the load better. No pics installed yet. AKBoards are being powder coated.

We are incorporating a tunnel brace into this design to strengthen the tunnel at the rear suspension mount.

Have you tested these on a PRO yet to see if they hold up to the everyday abuse?

 

[Hrt Offroad]

Can you give some close-up pics of the welds...they are all TIG welded I would presume...and Aluminum?

 

[907riders.com]

Can you give some close-up pics of the welds...they are all TIG welded I would presume...and Aluminum?

Yes these are aluminum tube boards and all connections are TIG welded. (first prototypes were mig welded and performing flawlessly)

I'm leaving for Kodiak Island at 0330 so I can't get a picture done for you right now but I will on Tuesday when I return to the shop.

Have you tested these on a PRO yet to see if they hold up to the everyday abuse?

We have been abusing these boards on several models, M-Series & Nytro this season and they are working beyond anyone's expectation. We guarantee you will be satisfied with the performance.

 

[Elfonzerio]

Do you live in the valley dude? I wouldn't mind checking these out, id rather support a local than buy elsewhere.

 

[pura vida]

they look pretty nice. good work. i absolutely love my airframes and won't ride without them again and these look like they will work as well. i also like to support local so might have to pick a set of these up for my next sled. (maybe next year...)

 

[907riders.com]

Do you live in the valley dude? I wouldn't mind checking these out, id rather support a local than buy elsewhere.

Yes. Off of green forest between bogard and palmer-wasilla.

I'm in Kodiak right now and will back on Tuesday.

 

[907riders.com]

they look pretty nice. good work. i absolutely love my airframes and won't ride without them again and these look like they will work as well. i also like to support local so might have to pick a set of these up for my next sled. (maybe next year...)

Thanks PV!

 

[k_newman66]

those look like they would work pretty slick. i made some just like that except used tubing along the tunnel and it builds up snow there. i think that flat stock would work alot better. wish i would of though of it. good idea

 

[kidrman]

Have you posted a pic on an M in the Cat section and I missed it?