engine

I am selling a used CPC (Cutler) big bore "dragoncat" kit I bought for my M7. Looking into it, the install is more involved and the tuning more difficult (after talking to Dale Cutler) than I was planning for. My loss is your gain. This kit requires the crankshaft to be rebuilt using Arctic Cat...

I am parting out my 2004 SkiDoo Rev 800 HO with 827 engine. Engine has 650 miles since complete rebuild including crank and bearings. Needs stator. Shocks off of 2008 SkiDoo XP. Bored carbs, SkiDoo Race Nun, RSI bars, good clutches, recently rebuilt primary, straight tunnel and rails. Good...

Hey everyone, so I recently bought a used pro rmk 800, and first ride I went to take it on after purchasing it the thing blew up. Brought it to my local Mechanic and he said everything is garbage in it, he have an estimate of around 5 grand to fix it when I paid 5500 for it so no too thrilled...

I have a 600 carb engine out of a 2007 IQ RMK with 2800 miles, 700 miles since crank was rebuilt. Top end in good condition when crank was rebuilt. Good compression in both cylinders. Comes with all attached parts recoil, carbs, exhaust valves. $1100 plus shipping.

I have a 600 carb engine out of a 2007 IQ RMK with 2800 miles, 700 miles since crank was rebuilt. Top end in good condition when crank was rebuilt. Good compression in both cylinders. Comes with all attached parts recoil, carbs, exhaust valves. $1100 plus shipping.

MOTOR RAN AMAZING BEFORE REMOVED FROM MACHINE, ONLY 25 MILES!!!! ITEM HAS VERY LOW MILES, LIKE NEW CONDITION, OEM PART. Item was removed from: 2016 SKI-DOO SUMMIT X E TEC 800 #00081. Only 25 miles on this item. Condition: Excellent used condition. Please refer to pictures. Asking $1900...

sold

I am considering parting out my 2008 Dragon 163, but only if the engine sells for what I need to get out of it. Engine is a Carls 860 big-bore system, it includes custom cast cylinders and head from Carls, ported cases, big bore pistons, rings. This engine has 1900 miles total on it since...

Hello All, I recently purchased a used RMK 700. I had the new sled for about two weeks prior to wrecking the engine in the sled. I haven't had much luck reaching anyone that might have a new engine for sale. I tore apart the engine to find out what happened and it looks to me like the piston...

I have a new in box m8 cylinder and piston works with 07-09 non ho motors. Looking for 200

Anyone seen any big bore kits, turbo kits etc for the little 600 motors? Maybe a idea for a custom turbo kit. Sled is a 2014 m6000 sno pro

So I managed to pick up a 05 M7 EFI 162" pretty cheap a few weeks ago, was in a hurry when I bought it and didn't go through the clutches very well. Anyway long story short, when I got it home there was a bad roller on the primary and the secondary looked like someone was trying to spread the...

so I took my 05 166 into the dealer to have the rest of the recalls done while it was there I had them do a couple other things as I was short on spare time. they did the fuel tank pump and harness, an alignment, and replaced the oiler cable for me.. took the sled out Saturday and it ran great...

Speedwerx 14:1 domes(5999-9999ft), comes with stock head and domes off a 06 M7. Call or text at 605-641-5825, 75$ + shipping, Thanks.

Have a nytro engine I wanna sell, has 300 km or so since full build with .060 head shim carillo rods head studs and gas ported pistons. Impulse turbo kit as well, terra alps tunnel and gas rack CR m10 rear skid low mile on rebuilt shocks, new sub fram with reinforcment plates, 2010 a arms new...

Have a nytro engine I wanna sell, has 300 km or so since full build with .060 head shim carillo rods head studs and gas ported pistons. Impulse turbo kit as well, terra alps tunnel and gas rack CR m10 rear skid low mile on rebuilt shocks, new sub fram with reinforcment plates, 2010 a arms new...

Time for new build so letting this one go. Has 3071 impulse turbo kit with standalone fuel system fuel system up to 16 on pump gas and 26 on race but most reliable and not takin over 18 lbs. 300 k on new motor with Carrillo rods, head studs and gas ported piston. Terra alps impulse tunnel and...

So I have a 2010 Dragon RMK with a Aerocharger turbo and a HM Turbos fuel controller on it. My check engine light is flashing which I know is supposed to be the pipe sensor. Bought a new one which was 190 bucks or something and put it in and still flashing. So I figured that with my luck I got a...

USED SLP Power Dome High Compression head for sale. I used this head for over 2000 miles. Its still in great shape with no nicks or dings inside domes and was taken off of a running and working motor. According to SLP it should run on pump gas. I found out that it actually needs a mix of...

I have a 2009 IQ chassis with all the electronics for the 4 injector engine but no engine. If you have one, shoot me an email at eugohmas@gmail.com. thanks.