electrical

Has anyone had any issues with the display gauge going out? My sled was running fine this weekend until it started cutting out on the top end and my display gauge was flickering on and off. now it wont even turn on or give me any feedback. My guess is I have a bad connection somewhere but I...

Ok. I have a 2011 Polaris 800 with pc5, auto tune, par 11.5 head slp pipe, can, v force reeds and adjustable heal clicker clutch weights. I have been chasing one of those gremlins for some time now. While running sled between idle and 7000 rpm all is well, try to run past 7200 rpm sled falls on...

My wife's 2009 summit 800 has developed a electrical problem. It will start and run when cold but after a few minutes of riding it acts like someone hits the kill switch. It has no spark after this happens but if you let it set for a while it will fire up and run again for a short time. I'm...

Got some stuff im thinking of selling off my 07 M8, let me know if you'd be interested. SLP single pipe and can. Secondary clutch with RK TEK 36 degree helix clutch kit. boon-docker box 6-900 N2O compatible. Send me an email dru7878@outlook.com and I can get you pictures

Before I get into tearing my 2007 rmk 600 apart... 1st: Can I rebuild my rear and front shocks or should I just replace them? 2nd: My speedo gauge flickers, sometimes doesn't stay on and my reverse light is staying on even when not engaged. 3rd: my steering has way too much play in it, is there...

Hey Guys, I have a 09 rs venture with 7000 miles. When riding it around on trails it will have a power glitch. It acts like it loses power then instantly gets it back. The screen goes blank and the speedometer cycles as if you were just turning it on. It then will stutter and then give a little...

09 M8 with Twisted Pump Gas Turbo I can't figure this sled out. Sometimes it will run awesome, sometimes it will stall, sputter and puke. Sometimes, when it does it stall and sputter thing, if I cut the power to the temp sensor on the bottom of the motor, it will run fine until the ECU senses...

Im currently doing some experiments with my sled, making up a custom wiring harness for a fuel controller or standalone EMS for use in turbo projects. but i have one major problem, does anyone know the part numbers /name and where it is possible to buy both the male and female connectors that...

So I bought my 09 M1000 with 800 miles on it, SLP pipe kit, over-sized air horn, PCV, cutler's clutching. The first ride it started doing something funny with the throttle like it wouldn't read the throttle, etc. Long story short, the next ride the exhaust temp sensor went out, I bought the GM...

So I did some testing last weekend on my sled. I've never had an issue with it before and I have ridden a few times this year. Halfway through the day it would die on me, it was like I hit the kill switch. It would start right up and run like a bat out of hell. It would start to die and I would...

I have an 06 900 and recently i had a screw come out inside stator/flywheel. I replaced both parts with used ones and now the sled wont stay running. A blink code flashes 9 times indicating a problem with the ignition coils but theyre sparking. it doesnt always flash sometimes its fine for a few...

I need a gauge cluster and steering post for a 2008 phazer MTX.

So I was riding my sled when it went completely dead out of no where. pulled it over a few times and none of the electronics were working. I had this problem before when my voltage regulator fried, had a spare so I installed it and it started up but then 5 seconds later smoke started coming from...

Wife's sled has about 500 miles on it. Ran most of today day just fine, then just died randomly at idle. Started it and none of the gauges worked, ran for a few second and died. I looked through all the wires and checked under the hood, but nothing. Put some snow on the electrical boxes and sat...

i have a '01 summit 800 and i just put an 8'' riser on it, in turn i had to extend all the wiring, throttle cable, and brake line. the problem is, i haven't gotten to ride it yet. the first time i went to ride it it started up fine, idled fine, but when i reved it up to 4000 rpm when the clutch...

Has new VR, worked fine for the first couple of hours. The ECU wasn't replaced but it didn't appear to be blistered on the back. Unplugged the handwarmers trying to see what has faulted? Can a bad stator be causing this? Any help is great Thanks!:frusty::frusty: