P
i am considering parting out the sled if there is enough interest. if it is parted out:
$3500 for 727 motor with pipe,can,carbs,cdi
$1500 for both front and rear suspensions including zero pros
make me an offer on everything else. i have a pretty good idea on what i want but too much to list. all details are listed below. i can email pics of sled. if not parted out the price is as listed, $5600
This sled is based off of an 2002 Polaris Edge 600 RMK 136” The sled currently has a Carl’s Cycle 727 motor and a 15X153X2.25 inch track, weights 460lbs wet without fuel (535-540lbs with fuel) with all tools and belts and ready to ride for the day. Comes with extra belts, extra gas tank, sway bar, cover, and has the Polaris RER (electronic reverse). $5600 o.b.o.
Call 907 355-5532
Motor Mods
• Carl’s Cycle 727 w/ ported cylinders and cases
• Bored carbs
• V-Force III reeds
• SLP single pipe and can
• SLP airbox and intake
• New pistons and rings
• New cylinders
• Team secondary clutch
Suspension Mods
• Holz trailing arms
• Holz spindles
• Fox zero pro front shocks
• Holz coil over rear suspension
• Fox zero pro rear shocks
• Holz big wheel kit
• SLP SLT skis
Chassis Mods
• Lightweight cowling w/custom powder bib (keeps snow off of pipe, out from underneath cowling)
2-2” Flo rites. Flo rite pre filters, tack only, no speedo
uses stock airbox and hinges
• Boss high rise widetop tanker seat (has 3 gallon tank in the seat)
• Challenger Extreme 153” X 2.25” track w/ 3.0 drivers
• Holz u-cooler (no bulkhead or tail coolers, much lighter)
• Holz handlebar 1” offset
• Tunnel extension
• Windshield bag
• Holz chaincase drop
• Motocross bars with 4” rise
• Clear gas tank
• Running board Snow Eliminators
• Sportech hand guards
$3500 for 727 motor with pipe,can,carbs,cdi
$1500 for both front and rear suspensions including zero pros
make me an offer on everything else. i have a pretty good idea on what i want but too much to list. all details are listed below. i can email pics of sled. if not parted out the price is as listed, $5600
This sled is based off of an 2002 Polaris Edge 600 RMK 136” The sled currently has a Carl’s Cycle 727 motor and a 15X153X2.25 inch track, weights 460lbs wet without fuel (535-540lbs with fuel) with all tools and belts and ready to ride for the day. Comes with extra belts, extra gas tank, sway bar, cover, and has the Polaris RER (electronic reverse). $5600 o.b.o.
Call 907 355-5532
Motor Mods
• Carl’s Cycle 727 w/ ported cylinders and cases
• Bored carbs
• V-Force III reeds
• SLP single pipe and can
• SLP airbox and intake
• New pistons and rings
• New cylinders
• Team secondary clutch
Suspension Mods
• Holz trailing arms
• Holz spindles
• Fox zero pro front shocks
• Holz coil over rear suspension
• Fox zero pro rear shocks
• Holz big wheel kit
• SLP SLT skis
Chassis Mods
• Lightweight cowling w/custom powder bib (keeps snow off of pipe, out from underneath cowling)
2-2” Flo rites. Flo rite pre filters, tack only, no speedo
uses stock airbox and hinges
• Boss high rise widetop tanker seat (has 3 gallon tank in the seat)
• Challenger Extreme 153” X 2.25” track w/ 3.0 drivers
• Holz u-cooler (no bulkhead or tail coolers, much lighter)
• Holz handlebar 1” offset
• Tunnel extension
• Windshield bag
• Holz chaincase drop
• Motocross bars with 4” rise
• Clear gas tank
• Running board Snow Eliminators
• Sportech hand guards